MCO3.0: No worry, we are still operating and ship order as usual. Stay safe.
Arduino
Arduino
Sort by
Show result

Features:

  • Bi-directional control for dual brushed DC motor.
  • Support motor voltage from 7VDC to 30VDC.
  • Maximum current up to 3A peak and 1.2A continuously, each channel.
  • Current limit protection.
  • Support 3.3V and 5V logic level input.
  • Stackable I/O header pin.
  • Selectable DIP switch mode for Signed Magnitude and Locked Anti-Phase.
  • Quick test switch for both channel.
  • Ready with connector for LSS05 (Auto-calibrate line sensor) for easy integration of line following robot.
  • No Polarity Protection For V Motor.
RM82.50

Features:

  • Bi-directional control for 1 brushed DC motor.
  • Support motor voltage ranges from 7V to 25V (Rev1.0), 7V to 30V (Rev2.0).
  • Maximum current up to 10A continuous and 15A peak (10 seconds).
  • 3.3V and 5V logic level input.
  • Solid state components provide faster response time and eliminate the wear and tear of mechanical relay.
  • Fully NMOS H-Bridge for better efficiency and no heat sink is required.
  • Regenerative Braking.
  • Speed control PWM frequency up to 10KHz.
  • Stackable I/O header pin.
  • Selectable digital pins for PWM and DIR.
RM54.72

Features:

  • Shield for Arduino form factor.
  • Bidirectional control for two brushed DC motor.
  • Control one unipolar/bipolar stepper motor.
  • Operating Voltage: DC 7V to 30V
  • Maximum Motor Current: 10A continuous, 30A peak
  • Buck regulator to produce 5V output (500mA max).
  • Buttons for quick testing.
  • LEDs for motor output state.
  • Selectable Arduino pins for PWM/DIR inputs.
  • PWM/DIR inputs compatible with 1.8V, 3.3V and 5V logic.
  • PWM frequency up to 20kHz (Output frequency is same as input frequency).
  • Overcurrent protection with active current limiting.
  • Temperature protection.
  • Undervoltage shutdown.
RM90.20

Specifications:

  • Logic control, 5V from Arduino main board
  • Polarity protection for External motor power input
  • 2 fast test buttons for each motor channel
  • 2 indicator LEDs for each channel
  • bi-directional control of two DC brush motor
  • Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
  • Up to 2A current each channel
  • Pin 4, 5,6,7 are used to drive two DC motor
  • Support PWM speed control
  • Support advance speed control
  • Socket for LSS05 - Auto-Calibrating Line Sensor, doing line following robot will be easy
RM43.00

Specification:

  • Dimension: 69mm x 52mm x 10mm
  • This version is optimized the use of Arduino compare to older version.
  • increase the pin socket, to facilitate the use of pin like 5V and GND.
  • 100% Arduino Compatible
  • Digital I / O digital input / output of 0 to 13 .
  • Analog I / O Analog Input / output of 0 to 5 .
  • PWM Pin - 3,5,6,9,10,11
  • Support ISP download function.
  • Input voltage : no external power supply when connected to the computer USB, external power supply 5V ~ 9V DC voltage input .
  • Output voltage : 5V DC voltage output and 3.3V DC voltage output .
  • Using Atmel Atmega328P microprocessor controller
  • This does not comes with cable. Cable is sell separately.
RM22.90

Specification:

  • Microcontroller: AT91SAM3X8E
  • Operating Voltage: 3.3V
  • Input Voltage (recommended): 7-12V
  • Input Voltage (limits): 6-16V
  • Digital I/O Pins: 54 (of which 12 provide PWM output)
  • Analog Input Pins: 12
  • Analog Output Pins: 2 (DAC)
  • Total DC Output Current on all I/O lines: 130 mA
  • DC Current for 3.3V Pin: 800 mA
  • DC Current for 5V Pin: 800 mA
  • Flash Memory: 512 KB all available for the user applications
  • SRAM: 96 KB (two banks: 64KB and 32KB)
  • Clock Speed: 84 MHz
  • Length: 101.52 mm
  • Width: 53.3 mm
  • Weight: 36 g
RM167.36

Specification:

  • Working with: Arduino Uno, Arduino Mega, Arduino Duemilanove.
  • Dimension: 70mm x 55mm x 10mm
RM38.00

Features:

  • Operate at 5V
  • Uses Arduino LCD4Bit library
  • Plug and Use with Arduino main board, no solder or fly-wiring needed.
  • 2x16 LCD.
  • 6 push buttons
  • Dimension: 80mm x 57mm x 12mm
  • Works with: Arduino Uno, Arduino Mega and Arduino Duemilanove.
RM12.10

Features:

  • ATmega32u4 Microcontroller
  • Input Voltage: 7-12V
  • 20 Digital I/O Pins
  • 7 PWM Channels
  • 12 ADCs
  • 16MHz Clock Speed
  • 32 KB Flash Memory
  • Require USB micro cable to load program
RM90.00

Features:

Microcontroller

ATmega2560

Operating Voltage

5V

Input Voltage (recommended)

7-12V

Input Voltage (limits)

6-20V

Digital I/O Pins

54 (of which 15 provide PWM output)

Analog Input Pins

16

DC Current per I/O Pin

20 mA

DC Current for 3.3V Pin

50 mA

Flash Memory

256 KB of which 8 KB used by bootloader

SRAM

8 KB

EEPROM

4 KB

Clock Speed

16 MHz

RM199.00

Specification:

  • Microcontroller: ATmega2560
  • Operating Voltage: 5VDC
  • Input Voltage (recommended): 7-12V through DC jack
  • Input Voltage (limits): 6-20V through DC jack
  • Digital I/O Pins: 54 (of which 14 provide PWM output)
  • Analog Input Pins: 16
  • DC Current per I/O Pin: 40 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 256 KB of which 8 KB used by the bootloader
  • SRAM: 8 KB
  • EEPROM: 4 KB
  • Clock Speed: 16 MHz
  • CH340 as USB to UART IC
  • USB B type socket for USB power and interface
RM55.00

Specification:

  • Microcontroller: ATmega32U4
  • Operating Voltage: 5V
  • Input Voltage (recommended): 7-12V
  • Input Voltage (limit): 6-20V
  • Digital I/O Pins: 20
  • PWM Channels: 7
  • Analog Input Channels: 12
  • DC Current per I/O Pin: 20 mA
  • DC Current for 3.3V Pin: 50mA
  • Flash Memory: 32 KB (ATmega32U4) of which 4 KB used by bootloader
  • SRAM: 2.5 KB (ATmega32U4)
  • EEPROM: 1 KB (ATmega32U4)
  • Clock Speed: 16 MHz
  • LED_BUILTIN: 13
  • Length: 48 mm
  • Width: 18 mm
  • Weight: 13 g
RM99.00

Features:

  • 4 digit 7-segment LED display module driven by two serial 74HC595's
  • 4 x surface mount LED's in a parallel configuration
  • 10K adjustable precision potentiometer
  • 3 x Independent push buttons
  • Piezo buzzer
  • Infrared receiver interface
  • Serial interface header for convenient connection to serial modules such as Bluetooth, wireless interface, voice module, a voice recognition module etc
RM18.70

Specification:

  • Microcontroller: Atmel ATmega328

  • Revision: 3.0

  • Original Arduino Nano from Arduino.cc

  • Operating Voltage (logic level): 5 VDC

  • Input Voltage (recommended): 7-12 V

  • Input Voltage (limits): 6-20 V

  • Digital I/O Pins: 14 (of which 6 provide PWM output)

  • Analog Input Pins: 8

  • DC Current per I/O Pin: 40 mA

  • Flash Memory: 32 KB (ATmega328) of which 2 KB used by bootloader

  • SRAM: 2 KB (ATmega328)

  • EEPROM: 1 KB (ATmega328)

  • Clock Speed: 16 MHz

  • Dimensions: 0.73" x 1.70"

RM92.45

Specification:

  • Arduino Nano compatible
  • Microcontroller: ATmega328P
  • Operating Voltage (logic level): 5 VDC
  • Input Voltage (recommended): 7-12 V, via Vin
  • Input Voltage (limits): 6-20 V, via Vin
  • Digital I/O Pins: 14 (of which 6 provide PWM output), same as Arduino UNO
  • Analog Input Pins: 8
  • DC Current per I/O Pin: 40 mA
  • Flash Memory: 32 KB (ATmega328P) of which 2 KB used by bootloader
  • SRAM: 2 KB (ATmega328P)
  • EEPROM: 1 KB (ATmega328P)
  • Clock Speed: 16 MHz
  • USB mini B socket for power and data
  • Uses CH340 instead of FT232 (Original Nano)
  • Dimension: 45mm x 18mm x 10mm
RM26.00